台湾东升平面不织布砂轮 100*10*16
更新时间：2010-01-01 00:00:00
价格：￥9/片
规格:100*10*16
类型:多款供选
材质:多款供选
联系电话：86 0760 22235298/22102237
联系手机：13924962545
联系人：
让卖家联系我
详细介绍
| 规格 | 100*10*16 | 类型 | 多款供选 |
| 材质 | 多款供选 | 工作线速度 | 35（M/S） |
| 圆度< | 1（μm） | 圆柱度< | 1（μm） |
| 粒度 | 46-320（目） | 适用范围 | 一般适用于一般金属，焊接缝，超硬钢等 |
| 形状 | 平形砂轮 | 结合剂 | 其他 |
德国进口材料,台湾东升,产品锐利耐用
| 精工细琢 专业品牌 | |||||||||||||||||||||||
| 树脂法研磨砂轮强度高弹性好,耐消耗, | 树 | ||||||||||||||||||||||
| 可作高转速研磨. | 脂 | ||||||||||||||||||||||
| 制法 | b法 | 法 | |||||||||||||||||||||
| 工件材质 | 研 | ||||||||||||||||||||||
| 一般钢材 | 素材 | 30a30kb | 磨 | ||||||||||||||||||||
| 已硬化处理 | wa36kb | 砂 | |||||||||||||||||||||
| 合金钢 | 素材 | wa36kb | 轮 | ||||||||||||||||||||
| 已硬化处理 | wa36jb | ||||||||||||||||||||||
| 工具钢 | 素材 | wa46ib | |||||||||||||||||||||
| 已硬化处理 | wa46hb | ||||||||||||||||||||||
| 不锈钢 | 400系列 | wa36jb | |||||||||||||||||||||
| 300系列 | wa36ib | ||||||||||||||||||||||
| 铸铁 | 一般铸铁 | c30kb | |||||||||||||||||||||
| 特殊铸铁 | gc36jb | ||||||||||||||||||||||
| kngdom 台湾东升专业砂布轮 高效 低耗 | |||||||||||||||||||||||
| 氧化铝纤维盘砂布轮 氧化锆纤维盘砂布轮 | |||||||||||||||||||||||
| 型号 | 尺寸 | 粒度 | |||||||||||||||||||||
| 40 | 60 | 80 | 100 | -400 | |||||||||||||||||||
| zp100 | 100*16 | ● | ● | ● | ● | ● | |||||||||||||||||
| zp115 | 115*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| zp125 | 125*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| zp150 | 150*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| zp180 | 180*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| 型号 | 尺寸 | 粒度 | |||||||||||||||||||||
| 40 | 60 | 80 | 100 | -400 | |||||||||||||||||||
| ap100 | 100*16 | ● | ● | ● | ● | ● | |||||||||||||||||
| ap115 | 115*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ap125 | 125*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ap150 | 150*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ap180 | 180*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| 订购指南 精工细琢 专业品牌 | ||||||||||||
| wa | 46 | k | 5 | v | 5 | a | 350x40x127 | |||||
| 磨料 | 粒度 | 结合剂 | 组织号 | 制法 | 型状 | 缘形 | 尺寸(dxtxh) | |||||
| 磨料粒度: | grit | |||||||||||
| 精度是用来表示磨料颗粒几何尺寸的大小,其选择 | grit is designated to represent the geometrical size of | |||||||||||
| 依据主要是加工工件所需要的表面粗糙度,同时也需 | abrasive grain.the grit size is chosen for customer"s | |||||||||||
| 考虑其他一些因素.以外圆磨为例,常用粒度与表面 | required surface finish as well as other conditions.for | |||||||||||
| 糙度有下面的大致关系: | example,in cylindricai grinding,there is relationship | |||||||||||
| between grit and surface finishes listed as bellow; | ||||||||||||
| 粒度 | 36-46 | 54-60 | 70-80 | 90-100 | grit | 36-46 | 54-60 | 70-80 | 90-100 | |||
| 粗糙度 | ra 1.6 | ra 0.8 | ra 0.4 | ra 0.2 | finish | ra 1.6 | ra 0.8 | ra 0.4 | ra 0.2 | |||
| ●粗料度的磨料适用于磨削: | ●use coarse grit: | |||||||||||
| 1)材质较软,延伸率大以及类似软铁和有色金属等 | 1.for soft,ductile,stringy material such as softsteel | |||||||||||
| 材料 | and nonferrous material | |||||||||||
| 2)进给量大,磨削速度要求高的场合. | 2.for rapid stock removal,high grinding speed | |||||||||||
| 3)表面粗糙度要求不高的场合. | 3.where finish is not important | |||||||||||
| 4)磨削接触面大的场合. | 4.for large areas of contact | |||||||||||
| ●细粒度的磨料适用于磨削: | ●use fine grit: | |||||||||||
| 1)硬度较高以及类似高碳工具钢,硬质合金钱类的金 | 1.for hard,brittle materials such as hard tool steels, | |||||||||||
| 属材料和玻璃等脆性材料. | cemented carbide and glass. | |||||||||||
| 2)表面粗糙度及精度要求高的场合. | 2.for fine finishes | |||||||||||
| 3)磨削接触面小的确场合. | 3.for small areas of contact | |||||||||||
| 4)工件半径或弧度小的场合. | 4.for holding small corner radii | |||||||||||
| 硬度: | grade: | |||||||||||
| e f g h i j k l m n o p q r | e f g h i j k l m n o p q r | |||||||||||
| 软----------------------硬 | soft------------------hard | |||||||||||
| 砂轮的硬度是指磨料之间的结合度,砂轮中结合 | the grade indicates the relative holding power of the | |||||||||||
| 剂量的多少决定了砂轮的硬度大小.用户需根据具 | bond which holds abrasive grains in a wheel.ln general, | |||||||||||
| 本的磨削(如进刀量,粗糙度,材质)要求来灵活选 | with a given type of bond it is the mount of bond which | |||||||||||
| 择砂轮的硬度. | determines a wheel"s should select the grade of a wheel | |||||||||||
| 一般砂轮硬度选择的原则是: | based on the grinding parameters such as feed rate. | |||||||||||
| finish re,materiials i.e..the following rules | ||||||||||||
| should be followed with regard to grade | ||||||||||||
| ●较软的硬度 | ●use soft grade: | |||||||||||
| 1)进刀量大的粗磨. | 1.for rapid stock removal | |||||||||||
| 2)磨削接触面大的场合. | 2.for large greas of contact | |||||||||||
| 3)材质较硬的工件,如高硬度工具钢和硬质合金钢等. | 3.for hard materials such as hard tool steels and carbide. | |||||||||||
| 4)工件抗热性能差,严防表面烧伤和磨削. | 4.for heat sensitive workpieces and grinding can not has | |||||||||||
| burning and discoloration on surface | ||||||||||||
| ●较硬的硬度 | ●use hard grade: | |||||||||||
| 1)进刀量小的精磨. | 1.for fine finish with little feed | |||||||||||
| 2)延长砂轮寿命. | 2.for longer wheel life | |||||||||||
| 3)材质较软的工件. | 3.for soft materials | |||||||||||
| 4)磨削接触面小或窄的场合. | 4.for small or narrow areas of contact | |||||||||||
| 组织号: 5 6 7 8 9 10 11 12 13 | structure: | 5 6 7 8 9 10 11 12 13 | ||||||||||
| 密--------------- 疏 | close------------open | |||||||||||
| 组织号用以表示砂轮内相邻的磨料颗粒之间的距 | the structure number indicates the space between neighboring | |||||||||||
| 离也就是间隙的大小.砂轮中磨料颗粒所占的体积百 | grains which can also be called grain spacing in a wheel the | |||||||||||
| 分比,也就是其浓度的大小,决定的砂轮的组织号.陶 | volume percentage of abrasive grains which represents the | |||||||||||
| 瓷砂轮组织号变化范围一般是从5到13,数字越小表 | density of grain in a wheel determines the structure number | |||||||||||
| 示砂轮组织越密,数字越大表示砂轮组织越疏松.组 | of a wheel.the structure of vitrified sheels ranges from 5 to | |||||||||||
| 织11,12和13通常是指气孔砂轮. | 13.the smaller the number,the more closed structure the wheel | |||||||||||
| the large the number,the more open structure wheel the numbers | ||||||||||||
| 11.12.13normally indicate porous wheels. | ||||||||||||
相关产品
联系方式
- 地址：中山 中山市小榄镇小榄大道南66号首层
- 电话：86 0760 22235298/22102237
- 联系人：未提供
- 手机：13924962545
- 传真：86 0760 22102500
公司官网
产品分类
站内搜索